Ridgid 535 Pipe Threader Troubleshooting: 4 Easy Ways to Fix it

Facing problems with your Ridgid 535 pipe? Well, don’t worry. We have briefly mentioned every problem and solution for those.

So, you might be wondering about the process of Ridgid 535 Pipe Threader Troubleshooting?

Ridgid 535 pipe threader can face multiple problems. For starters, it can be an electrical issue. If that’s the issue don’t use extension cords. Secondly, it can be torn threads. To overcome it use improper cutting. Next for the alignment issues, be careful about material placement.

These all might seem confusing at first. But, don’t worry. We’ll cover everything in the next few sections regarding it.

So, let’s start!

Ridgid 535 Pipe Threader: 4 Common Problems

A pipe threader is a great tool for cutting off materials. However, even the best tools face problems. For instance, problems with Miller 250x can surface from improper application.

Ridgid 535 Pipe threader

Despite being one of the best pipe threaders, Ridgid 535 pipe threader can also face multiple problems. Some common yet critical issues are:

Problem 1: Electrical Issues

The failure of threading capacity is a typical electrical problem with the Ridgid 535 Pipe Threader. When using an electrical cord, the equipment is prone to voltage sags. This is especially sensitive with the Ridgid 535 pipe threader, which runs on 115 volts.

Problem 2: Torn Threads

Another common problem for Ridgid 535 pipe threader is torn threads. It hampers the initial purpose of using the pipe threader. The end thread or groove becomes unusable which is a major issue.

Problem 3: Die Heads Movement

When using Ridgid 535 pipe threader, the die head should be stationary. Using this machine you can move it and cut grooves according to your needs. If the die heads move then getting the perfect thread will be impossible.

Problem 4: Alignment Issue

Ridgid 535 pipe threader alignment issue is mostly caused by the user. Poor threads will come out if materials are misaligned. 

These are the problems of the Ridgid 535 pipe threader. From the same manufacturer, Ridgid miter saw guard problems can also occur.

Let’s see the Ridgid 535 threader troubleshooting in the next section.

Ridgid 535 Pipe Threader Troubleshooting

Looking to troubleshoot Ridgid 535 pipe threader? Well, We got everything covered.

Source: ridgidforum.com

Let’s see all the problems and solutions to those below.

Problem 1 of 4 Electrical Issues

As we have mentioned, Ridgid 535 pipe threader uses 115 volts of electricity. So, any certain mistake can cause electrical issues.

For starters, using cord extension can cause electricity disruption. Because it loses the power that is required to operate. Also, it causes voltage sags which can damage the components as well as Ridgid 535 Pipe Threader specs.

Also, inadequate or no grounding pin can cause shock. It runs electricity through every electric conduct material like metal.

The problems seem critical. But solutions are simple for this problem. 

Solution

Firstly, you should avoid using an extension cord. If it is not possible, then use a 2.6mm cord wire up to 10 feet. However, even that long cord can be insufficient. So, using a 3.2mm extension code wire up to 10 feet is advised.

Secondly, properly grounding the machine is a must. You need to check if your workshop is properly earthed or not. 

To do so, insert a circuit tester and check your machine. If any light doesn’t blink then good news! Your machine is fully safe. If the light blinks, call a professional to get your workshop wiring grounded.

Here are some top-grossing multimeters/circuit testers you can use:

You can get an accurate reading of whether your machine is properly grounded or not.

Problem 2 of 4 Torn Threads

You might be thinking why is my pipe threader breaking threads? Well, the reasons can be improper cutting fluids, dull dies, too speedy or hard material.

Let’s see the solution for each stated case.

Solution

First, improper cutting fluids can be a reason. Ridgid manufacturers always advise using Nu-Clear pipe threading oil. However, low or empty oil reservoirs can also be the reason why threads are breaking. So, always keep the reservoirs full.

Secondly, dies are the way to get the thread you need. Nevertheless, these are metal components. So, it gets dull easily. To resharpen it, you need the grind the surface. Then, removing broken or chipped teeth from the die can do the trick.

Thirdly, the different thread needs to be cut at a different speed. Use the user manual of the Ridgid threader to see the speed for each tool.

Lastly, another reason why the threads are breaking is hard material. To avoid such things from happening use the right die, speed, and pressure.

Problem 3 of 4 Die Heads Movement

Unusual Die head movements can happen for loose bolts, uncleaned slots, and, worn slots or linkage.

The solutions for the issues are dictated below.

Solution

To start with check if the bolts of die heads attached to the machine are loose. If those are loose, then use a screwdriver to tighten them. You need to go counter-clockwise to tight them.

Next, die head slots can be uncleaned. It can happen due to oil stains or dirt. Either way, you need to clean it by applying baking soda. Leave that for a couple of hours. Then rinse it off with warm water and a clean cloth.

Secondly, for worn slots and linkage, you can easily change the linkage. However, for the worn slots, you have to completely change the dies.

Problem 4 of 4 Alignment

We have already mentioned that the alignment issue happens because of the user. It is, however, not a major problem, yet a common one. 

The solution to it is much simpler than others. Let’s see that.

Solution

Firstly, place the material in the chuck and bring it together with the die head. During the same period, the substance should contact all the die parts’ throats.

That’s all about the common problems and solutions to those. These will help your Ridgid 535 pipe threader to work just as before.

Maintenance

Just like any other machinery, Ridgid 535 pipe threader needs to be maintained well. Below, the proper pipe threader maintenance is explained..

Turn It off After Using

Ridgid 535 pipe threader is a sensitive tool. Also, it consumes lots of electricity. Also, keeping the power on overnight kills efficiency. So, it’s ideal to turn it off.

Inspect Every Component

Every component of the Ridgid 535 pipe threader is essential. Also, Ridgid 535 pipe threader parts cost a lot. So, inspect the components weekly to see if any issues arise.

Clean Oil Reservoirs

Old oils create slugs and hamper efficiency. To clean the oil reservoirs, you need to first drain the whole system. Then, use a microfibre cloth to clean oil stains, slugs, or paint. Then, you can add new oil to it.

FAQs

What is the Weight of Ridgid 535 Pipe Threader?

Ridgid 535 pipe threader is an industrial-grade tool. So, naturally, it weighs 285 pounds or 130 kg.

What Types of Die Heads are Used for Ridgid 535 Pipe Threader?

Ridgid 535 uses two types of die heads. Those are manual die heads and machine die heads. Manual die heads have dies that are specific to a given size and thread profile. Machine Die heads range in size from 1/4 to 4 inches.

What is the Range of Different Forms of Pipe Threads and Connections?

There are 6 different forms of pipe threads and connections. Those are UN/UNF,

NPT/NPTF, BSPP (BSP, parallel), BSPT, metric parallel, and, metric tapered.

Conclusion

That is all about the Ridgit 535 pipe threader troubleshooting. 

Whenever the oil reservoir is half full, add oil for efficient usage of oil. That way, you can save lots of oil.

Have a great day and take care!

Leave a Comment

Your email address will not be published.

Scroll to Top